首页 资讯 应用 高压 设计 行业 低压 电路图 关于

轨道交通

旗下栏目: 轨道交通 新能源 智能装备 汽车电子

HXN3型内燃机车串行输出信号(五)

轨道交通 | 发布时间:2017-09-04 | 人气: | #评论# |本文关键字:HXN3,参数,串行输出信号
摘要:Serial Output Signals-串行输出信号 Display Name 显示名称 : Chinese Display Name Description 说明 : 中文简要说明/Chinese description BL1 En BL1 有效 Enable signal for Aux Inverter 9 辅助逆变器9有效 BL1FRun BL1 频率

Serial Output Signals-串行输出信号

Display   Name
    显示名称:
Chinese Display   NameDescription说明:中文简要说明/Chinese   description
 BL1 En  BL1有效Enable   signal for Aux Inverter 9  辅助逆变器9有效
 BL1FRun  BL1频率控制Frequency   command for Aux Inverter 9  辅助逆变器9频率控制
 BarPrsP  大气压力Barometric   Pressure  大气压力
 CC1 En  CC1有效Enable   signal for Aux Inverter 16  辅助逆变器16有效
 CC1FRun  CC1频率控制Frequency   command for Aux Inverter 16  辅助逆变器16频率控制
 CC2 En  CC2有效Enable   signal for Aux Inverter 17  辅助逆变器17有效
 CC2FRun  CC2频率控制Frequency   command for Aux Inverter 17  辅助逆变器17频率控制
 EgSpRq  柴油机速度指令The   engine speed request that EMDEC should use to control the engine speed.  柴油机速度指令
 EgStLk>  柴油机启动锁定Signal   to FIRE that the protective engine start lockout has been set, and a password   is required to start the engine. First used for crankcase pressure shutdowns   on H engines. See system sec 11.2.9 for details.  柴油机起停锁定有效:柴油机密码起动。信号连接到FIRE,首先用于H机曲轴箱压力关闭。见系统11.2.9
 IcWDiai  机车平均轮径The   average wheel diameter of all the wheels on the locomotive.  机车平均轮径
 LCFs HB  LCFs心跳This   signal is the application layer heartbeat for the LCC (EM2000) fast control   task. It can be broadcast by the LCC to any other system or application to   determine the LCC fast control task health. It is a byte-sized unsigned   number that increases by one during every execution of the fast control task.   It is first used on RAILCAN-equipped locomotives including the Alstom NJT   20009435 order.  机载计算机(EM2000)快速控制任务应用层心跳。其他系统或应用依此判断该快速控制的有效性。无符号字节,每执行一次加一。用于RAILCAN机车包括Alstom   NJT 20009435
 LCMd Hb  LCMd心跳This   signal is the application layer heartbeat for the LCC (EM2000) medium control   task. It can be broadcast by the LCC to any other system or application to   determine the LCC medium control task health. It is a byte-sized unsigned   number that increases by one during every execution of the medium control   task. It is first used on RAILCAN-equipped locomotives including the Alstom   NJT 20009435 order.  机载计算机(EM2000)中速控制任务应用层心跳。其他系统或应用依此判断该快速控制的有效性。无符号字节,每执行一次加一。用于RAILCAN机车包括Alstom   NJT 20009436
 LCSl Hb  LCSI心跳This   signal is the application layer heartbeat for the LCC (EM2000) slow control   task. It can be broadcast by the LCC to any other system or application to   determine the LCC slow control task health. It is a byte-sized unsigned   number that increases by one during every execution of the slow control task.   It is first used on RAILCAN-equipped locomotives including the Alstom NJT   20009435 order.  机载计算机(EM2000)慢速控制任务应用层心跳。其他系统或应用依此判断该快速控制的有效性。无符号字节,每执行一次加一。用于RAILCAN机车包括Alstom   NJT 20009437
 LcAC HB  LcAC心跳CAN   heartbeat sent to Auxiliary inverters  CAN心跳   : 送至辅助逆变器
 RF1 En  RF1有效Enable   signal for Aux Inverter 0  辅助逆变器0启用
 RF1FRun  RF1频率控制Frequency   command for Aux Inverter 0  辅助逆变器0频率控制
 RF2 En  RF2有效Enable   signal for Aux Inverter 1  辅助逆变器1启用
 RF2FRun  RF2频率控制Frequency   command for Aux Inverter 1  辅助逆变器1频率控制
 RF3 En  RF3有效Enable   signal for Aux Inverter 2  辅助逆变器2启用
 RF3FRun  RF3频率控制Frequency   command for Aux Inverter 20  辅助逆变器20频率控制
 SptMode  移车状态Mode   of the AC spotter control state machine - see 3.11.2  移车控制状态   - 见3.11.2
 SptStat  移车故障代码Error   message associated with AC spotter operation  移车操作故障
 T1AFBnk  T1故障数据Indication   of active fault data bank for the MPU trace memory recorder to use.  转向架1错误数据库:用于转向架1微处理器跟踪存储记录器
 T1BWS>  T1空转A   TRUE value indicates that the LCC desires the TCC to activates its wheel slip   system. 转向架1空转启用有效
 T1BusyA  T1电机有效Busy   Check: The TCCs will add one to this signal and then send it back as a serial   input. The LCC should reflect this number back to each TCC. The process will   then repeat, continuously. Failure of the TCC to respond properly indicates a   failed communications link.  转向架1牵引电机连接自检发送:检查机载计算机和个牵引电机的连接
 T1DCL V  主发1输出电压The   main alternator DC output voltage. Used for SWETS only.  转向架1主发直流输出电压
 T1MxPMT  T1相模块最高温度The   maximum of the three phase module temperatures  转向架1三相模块温度最大值
 T1N+dN  T1转矩调整MELCO   IGBT Inverter: 4-Pole Motor - The maximum motor speed that TCC should allow,   regardless of the torque reference. We process this in the slow loop, so it   is sent slow. (Not doing so can cause brief unloads when the radar fails.   10/20/99 )  转向架1牵引电机允许IGBT电机速度极值:在慢环路处理   (否则会造成瞬时卸载)
 T1Oper>  T1输出转矩Flag   from the Sequence Controller indicating that the MPU can produce flux and   torque  转向架1输出扭力:   信号自顺序控制器
 T1SptM>  T1移车工况Output   to MPU for spotter mode.  转向架1移车工况
 T1TM1RM  电机1轮径系数Ratio   of wheel diameter to reference wheel diameter  转向架1牵引电机1轮径系数:对照参考轮径
 T1TM2RM  电机2轮径系数Ratio   of wheel diameter to reference wheel diameter  转向架1牵引电机2轮径系数:对照参考轮径
 T1TM3RM  电机3轮径系数Ratio   of wheel diameter to reference wheel diameter  转向架1牵引电机3轮径系数:对照参考轮径
 T1Tor R  T1转矩参考MELCO   IGBT Inverter: Inverter Torque Reference is the torque reference requested by   the LCC.  转向架1牵引逆变器扭矩参照
 T2AFBnk  T2故障数据Inidication   to the MPU of the fault data bank for the trace memory recorder to use  转向架2错误数据库:用于转向架1微处理器跟踪存储记录器
 T2BWS>  T2空转A   TRUE value indicates that the LCC desires the TCC to activates its  wheel slip system. 转向架2空转启用有效
 T2BusyA  T2电机有效Busy   Check: The TCCs will add one to this signal and then send it back as a serial   input. The LCC should reflect this number back to each TCC. The process will   then repeat, continuously. Failure of the TCC to respond properly indicates a   failed communications link.  转向架2牵引电机连接自检发送:检查机载计算机和个牵引电机的连接
 T2DCL V  主发2输出电压The   main alternator DC output voltage. Used for SWETS only.  转向架2主发直流输出电压
 T2MxPMT  T2相模块最高温度The   maximum of the three phase module temperatures  转向架2三相模块温度极值
 T2N+dN  T2转矩调整MELCO   IGBT Inverter: 4-Pole Motor - The maximum motor speed that TCC should allow,   regardless of the torque reference.  转向架2牵引电机允许IGBT电机速度极值:在慢环路处理   (否则会造成瞬时卸载)
 T2Oper>  T2输出转矩Flag   from the Sequence Controller indicating that the MPU can produce flux and   torque  转向架2输出扭力:   信号自顺序控制器
 T2SptM>  T2移车工况 Output to MPU for   spotter mode  转向架2移车工况
 T2TM1RM  电机4轮径系数Ratio   of wheel diameter to reference wheel diameter  转向架2牵引电机1轮径系数:对照参考轮径
 T2TM2RM  电机5轮径系数Ratio   of wheel diameter to reference wheel diameter  转向架2牵引电机2轮径系数:对照参考轮径
 T2TM3RM  电机6轮径系数Ratio   of wheel diameter to reference wheel diameter  转向架2牵引电机3轮径系数:对照参考轮径
 T2Tor R  T2转矩参考MELCO   IGBT Inverter: Inverter Torque Reference is the torque reference  requested by the LCC. 转向架2IGBT逆变器扭力参照
 ThrPos  主手柄位置Throttle   Position  主手柄位置
责任编辑:电气自动化网

热门文章

首页 | 资讯 | 应用 | 高压 | 设计 | 行业 | 低压 | 电路图 | 关于

Copyright 2017-2018 电气自动化网 版权所有 辽ICP备17010593号-1

电脑版 | 移动版

Ctrl+D 将本页面保存为书签,全面了解最新资讯,方便快捷。