首页 资讯 应用 高压 设计 行业 低压 电路图 关于

轨道交通

旗下栏目: 轨道交通 新能源 智能装备 汽车电子

HXN3型内燃机车数字输出信号参数表

轨道交通 | 发布时间:2017-09-04 | 人气: | #评论# |本文关键字:HXN3,参数,数字量信号
摘要:Digital Output Signals-数字量输出信号 Display Name 显示名称 : Chinese Display Name Description 说明 : 中文简要说明/Chinese description AComp3 启动空压机 Air Compressor #3: A TRUE value causes the contactor to close a

Digital Output Signals-数字量输出信号

Display   Name
    显示名称:
Chinese Display   NameDescription说明:中文简要说明/Chinese   description
AComp3>  启动空压机>Air   Compressor #3: A TRUE value causes the contactor to close and power to be   applied to the auxiliary air compressor.  空压机   3: 有效时接触器闭合供电
APCINH>  APC禁止>Auxiliary   Power Converter Inhibit: This output is set TRUE when APC operation is to be   suspended.  APC输出禁止
APCRST>  APC复位>Auxiliary   Power Converter Reset: This output is set TRUE when an APC fault is to be   reset.  APC复位
Appl1>  I端电器设备>Appliance   Inverter #1 Contactor: A TRUE value causes the contactor to close which   activates the #1 appliance inverter.  电器逆变器1接触器闭合
Appl2>  II端电器设备>Appliance   Inverter #2 Contactor: A TRUE value causes the contactor to close which   activates the #2 appliance inverter.  电器逆变器2接触器闭合
ASDsbl>  自动起停关闭>Auto   Start Disable: A value of TRUE activates the Auto Start Disable indicator   output 自动起停关闭信号灯控制
ASEnab>  自动起停启动>Auto   Start Enable: A value of TRUE activates the Auto Start Enable indicator   output自动起停启用信号灯控制
ASInac>  自动起停无效>Auto   Start Inactive: A value of TRUE activates the Auto Start Inactive indicator output  自动起停停止信号灯控制
B1>  B1控制>B1   Contactor: A value of TRUE causes the contactor to close.  B1接触器控制
B2>  B2控制>B2   Contactor: A value of TRUE causes the contactor to close.  B2接触器控制
B3>  B3控制>B3   Contactor: A value of TRUE causes the B3 contactor to close.  B3接触器控制
B4>  B4控制>B4   Contactor: A value of TRUE causes the B4 contactor to close.  B4接触器控制
BC>  BC控制>Battery   Charging contactor: A value of TRUE causes the battery charging contactor to   close.  蓄电池充电接触器闭合
BkHtr1>  后墙暖气1>Backwall   Heater #1 Contactor: A TRUE value causes the contactor to close.车后墙加热器1接触器闭合
BkHtr2>  后墙暖气2>Backwall   Heater #2 Contactor: A TRUE value causes the contactor to close.车后墙加热器2接触器闭合
BWR>  电制预警>Brake   Warning Relay: A value of TRUE causes the relay to close.  制动警告继电器
CAF>  辅发预励磁>Companion   Alternator field Flash contactor: A value of TRUE causes the CA Field   Flashing contactor to close. This connects the battery to the CA field in   order to start the Auxiliary Power Converter.  副发电机励磁预激接触器
ChpCbr>  斩波器保护>Chopper   Crowbar command output. Used with MG Field Supply Chopper Traction Alternator   Field Control Device.  斩波器过压保护输出
ChpRst>  斩波器重置>Chopper   fault Reset command output. Used with MG Field Supply Chopper Traction   Alternator Field Control Device.  斩波器故障复位输出
D Valv>  停机阀>Governor   D Valve: A value of TRUE activates the governor's D valve.  调速器D
DCCl>  DCL闭合>DC   Link Closed Switch-gear Output: A TRUE value will cause the DC link   switch-gear to rotate toward the closed position. The closed position   connects inverters to the DC link.  中间直流环节转换开关闭合输出:接通逆变器
DCOp>  DCL断开>DC   Link Open Switch-gear Output: A TRUE value will cause the DC link switch-gear   to rotate toward the open position. The open position disconnects all   inverters from the DC link.  中间直流环节转换开关断开输出:断开逆变器
DCR>  干燥器>Air   Dryer Control Relay output. Asserting output picks up relay, which in turn   activates the air dryer. 空气干燥器继电器输出
EBT>  间隔吹扫>Electronic   Blowdown Timer Relay: A TRUE value causes the relay to close and initiate a   small release of air from the main air reservoir.  电子时间继电器:闭合并从主风槽少量放气
ECTrip>  备用停机>Engine   Control CB Trip: This output energizes a trip coil on the Engine Control CB   to stop the diesel engine.  柴油机控制断路器跳闸控制:柴油机后备停机控制
ERR>  柴油机运转>Outpu control for Engine   Running Relay ERR. 柴油机运转继电器
ERV>  动力间通风>Output   to Engine Room Ventilation Blower  柴油机室通风机
ESC>  紧急撒沙控制>Emergency   Sand Control: A value of TRUE causes this trelay to pick up.  紧急撒砂继电器:闭合有效
ESWarn>  启动警报>Engine   Start Warning: This output is used to drive a Klaxon alarm device which   indicates that the engine start sequence is about to begin.柴油机起机警告
FCF1>  风扇1高速>Fast   Speed Fan Contactor #1: A TRUE value causes the FCF1 contactor to close.FCF1高速风扇接触器控制
FCF2>  风扇2高速>Fast   Speed Fan Contactor #2: A TRUE value causes the FCF2 contactor to close.FCF2高速风扇接触器控制
FCS1>  风扇1低速>Slow   Speed Fan Contactor #1: A TRUE value causes the FCS1 contactor to close.FCS1低速风扇接触器控制
FCS2>  风扇2低速Slow   Speed Fan Contactor #2: A TRUE value causes the FCS2 contactor to close.FCS2低速风扇接触器控制
FP Rly>  燃油继电器>Fuel   Pump Relay: A value of TRUE activates the fuel pump relay. 燃油泵继电器
FtHtr1>  脚炉1>Foot   Heater #1 Contactor: A TRUE value causes the contactor to close .脚暖1接触器闭合
FtHtr2>  脚炉2>Foot   Heater #2 Contactor: A TRUE value causes the contactor to close.脚暖2接触器闭合
GFC>  主发励磁>Generator   Field Contactor: A value of TRUE energizes the contactor. 主发励磁接触器
GFD>  主发励磁放电>Generator   Field Decay Contactor: A TRUE value causes the GFD contactor to close.  主发励磁削减接触器
GR Rst>  接地复位>Ground   Relay Reset Coil: A TRUE value energizes the reset coil of the ground relay.接地继电器复位线圈
HWR1>  电热玻璃I>Heated   Windshield Relay Cab #1: A TRUE value causes the relay to pick up.驾驶室1前挡风暖风继电器闭合
HWR2>  电热玻璃II>Heated   Windshield Relay Cab #2: A TRUE value causes the relay to pick up.驾驶室2前挡风暖风继电器闭合
LCC OK>  微机正常>Locomotive   Control Computer OK: A value of TRUE causes the LCC relay to pick up. 机车控制微机正常
LDBFSA>  除尘风机高速>Locker/Dust   Bin Blower Motor Fast:  A value of TRUE causes the LDBFSA contactor   to pick up电气间风机马达高速接触器闭合
LDBSS>  除尘风机低速> Locker/Dust   Bin Blower Motor Slow:  A value of TRUE causes the LDBSS contactor   to pick up电气间风机马达低速接触器闭合
LSC CO>  移车切除> Locomotive   Spotter Cutout. A TRUE value causes the spotter circuit to be cut out using   the motor operated switch gear.移车主回路转换开关
LSC>  移车接触器> Locomotive   Spotter Contactor: A TRUE value causes that contactor to pick up.机车移车接触器
MV SH>  百叶窗>Cooling   Fan Shutters Magnet Valve: A TRUE value will energize the magnet valve.冷却风扇百叶窗控制
MVASAL>  启动执行左>Magnet   Valve Air Start Actuate Left Control:    When this &  STE signals are TRUE air is admitted to the   left start motor to crank the engine.柴油机起动左侧执行控制电磁阀
MVASAR>  启动执行右>Magnet   Valve Air Start Actuate Right   Control:  When this &  STE signals are TRUE air   is admitted to the right start motor to crank the engine.柴油机起动右侧执行控制电磁阀
MVASEL>  启动啮合左>Magnet   Valve Air Start Engage Left Control: When this & STE are TRUE, air is   admitted to the left air start motor to engage the gears.柴油机起动左侧啮合控制电磁阀
MVASER>启动啮合右>Magnet   Valve Air Start Engage Right Control: When this & STE are TRUE, air is   admitted to the right air start motor to engage the bendix.柴油机起动右侧啮合控制电磁阀
MVCCR1>  空压机1>MVCC   #1 Magnet Valve: A value of TRUE activates the #1 air compressor   magnet valve.1号空压机电磁阀运行
MVCCR2>  空压机2>MVCC   #2 Magnet Valve: A value of TRUE activates the #2 air compressor   magnet valve.2号空压机电磁阀运行
MVECRN>  喷射阀>Engine   Crankcase Eductor Magnet Valve: A value of TRUE activates the eductor magnet   valve.柴油机曲轴箱喷射器电磁阀运行
MVPE>  减压阀>Magnet   Valve Pressure Exhaust Control: When this output is TRUE, a magnet valve is   picked up to open shutters to relieve (exhaust) pressure  in the carbody to allow personnel to walk   through.车内减压电磁阀控制:   车体减压方便人员通过
MVS 1F>  前架前撒沙>Truck   #1 Forward Sanding Magnet Valve: A value of TRUE causes the  valve to open and the forward sanders of   truck #1 to be activated.  转向架1前撒砂电磁阀开启:撒砂启动
MVS 1R>  前架后撒沙>Truck   #1 Reverse Sanding Magnet Valve: A value of TRUE causes the  valve to open and the reverse sanders of   truck #1 to be activated.  转向架1后撒砂电磁阀开启:撒砂启动
MVS 2F>  后架前撒沙>Truck   #2 Forward Sanding Magnet Valve: A value of TRUE causes the  valve to open and the forward sanders of   truck #2 to be activated.  转向架2前撒砂电磁阀开启:撒砂启动
MVS 2R>  后架后撒沙>Truck   #2 Reverse Sanding Magnet Valve: A value of TRUE causes the  valve to open and the reverse sanders of   truck #2 to be activated.  转向架2后撒砂电磁阀开启:撒砂启动
No AR>  无报警>NO   Alarm Relay: A TRUE output indicates that the AR relay is NOT active and that   2T is NOT energized.无报警继电器输出
RadBlw>  雷达吹扫>Radar   Air Blower Valve: A TRUE value energizes the radar air-blow valve which   causes compressed air to blow across the radar's face plate. 雷达通风阀:压力空气吹雷达前面板
SdHtr1>  侧墙暖气1>Sidewall   Heater #1 Contactor: A TRUE value causes the contactor to pick up.车侧壁加热器1接触器:   闭合有效
SdHtr2>  侧墙暖气2>Sidewall   Heater #2 Contactor: A TRUE value causes the contactor to pick up.车侧壁加热器2接触器:   闭合有效
STE>  启动允许>Start   Enable: A TRUE value energizes the STE relay coil.启动允许继电器
TI1CO>  前架切除>TCC   #1 Inverter Cutout Solenoid: A TRUE value causes the cutout solenoid to be   activated.前架相模块切除
TI2CO>  后架切除>TCC   #1 Inverter Cutout Solenoid: A TRUE value causes the cutout solenoid to be   activated.后架相模块切除
TLP RV>  滑油泵反转>Turbo   Lube Pump ReVerse Relay. A value of TRUE causes this relay to pick up . 增压器滑油泵反向继电器
TLPR>  滑油继电器>Turbo   Lube Pump Relay: A value of TRUE causes this relay to pick up.  增压器滑油泵继电器
Wh Slp>  空转>Wheel   Slip Relay: A TRUE value causes the relay to close which activates the wheel   slip light.  空转继电器:继电器闭合,显示屏上的空转指示亮
WSCAF>  外电源励磁>Wayside   CA Field Isolation Contactor: A TRUE value causes the wayside CA field   isolation contactor to be energized.  外电源辅发励磁接触器


责任编辑:电气自动化网

热门文章

首页 | 资讯 | 应用 | 高压 | 设计 | 行业 | 低压 | 电路图 | 关于

Copyright 2017-2018 电气自动化网 版权所有 辽ICP备17010593号-1

电脑版 | 移动版

Ctrl+D 将本页面保存为书签,全面了解最新资讯,方便快捷。